Electro-dynamic Shakers simulate real-world environments to investigate dynamic endurance and ascertain reliability in select fields of vibration testing.
This low sturdy force rating are specially designed for testing of wide range of products, be it electronics, automotive and defence applications. This series shaker generates high velocity which is required for shock applications.
As a standard configuration, the shaker is supported on a frame with a trunnion assembly for 90 degree tilt. Shaker itself has pneumatic body isolation and is cooled by a water cooled system and is interlocked with the amplifier console for operational safety.
The shaker's electromagnet and moving element are energized by the direct current and alternating current supplies respectively generated and are electronically interlocked to the power amplifier drive console.
The solid-state Power Amplifier is an intelligent microcontroller based console in a movable rack version. It has a feather-touch user-friendly interface at the front panel to drive the respective Electro-dynamic Shaker.
The PC based Remote Link Module can be optionally used to remotely operate the complete vibration system. It is based on a chip-board microcontroller and is driven by software commands to communicate identical functions of the amplifier's control panel e.g. Gain, FPS, Cooling, Start-up and Shutdown. All the critical parameters like output voltage, current, temp., and all system interlocks are displayed simultaneously.
DEV 590-DPA 190K
DEV 590-DPA 240K
|Armature diameter||590 mm||590 mm|
|Sine force (peak)||16000 Kgf (35200 lbf)||20000 Kgf (44000 lbf)|
|Random force (rms)||16000 Kgf (35200 lbf)||20000 Kgf (44000 lbf)|
|Shock force||35000 Kgf (77000 Ibf)||45000 Kgf (99000 Ibf)|
|Acceleration (Sine)||100 'g'||100 'g'|
|Velocity (sine peak)||2.0 m/sec||2.0 m/sec|
|Displacement (Pk-pk)||51mm(2 Inch)||51mm(2 Inch)|
|Axial Resonance (±5%)||1700Hz||1700Hz|
|Useful Frequency range||5 to 2000Hz||5 to 2000 Hz|
|Protection Interlocks||Mains input Over & Under Voltage, Over Current, Loss of Input Phase, Over Temperature Amplifier & Shaker, Cooling flow, Field fail, User safety interlock or if specifically required by customer.|
|Moving element mass||160kg||200kg|
|Internal load capability||3000 Kg||3000 Kg|
|Suspension axial stiffness||28Kg/mm||28Kg/mm|
|Suspension cross-axial stiffness||3200 Kg/mm||3500 Kg/mm|
|Stray magnetic field (150mm above table)||10 gauss||10 gauss|
|Cooling flow (Water Cooled)||Close loop water cooled system|
|Compressed air (utility required at site)||6 Bar||6 Bar|
|Shaker body mass||15000 Kg||18000 Kg|
|Dimensions (L x W x H) (mm)||1800 x 1400 x 1360||1800 x 1400 x 1360|
|Power output||190 KVA||240 KVA|
|Total harmonic distortion (At resistive load)||Typically 0.5%||Typically 0.5%|
|Input impedance (Nominal)||10 k Ohm||10 k Ohm|
|Input sensitivity||4 V rms Compatible with all standard controllers|
|Signal-to-Noise ratio||> 75 dB||> 75 dB|
|Power efficiency||> 90%||> 90%|
|Protection||Integral protection to prevent the output devices working beyond their specification limits.|
|EMC||EN50081-2 Emissions and EN50082-2 Immunity|